A second area of disagreement was what signals should be supported on the new PCIe connector. If the first and second generation PC/104-Plus connectors would be gradually phased out, shouldn't there be some low speed I/O interface signals included on the PCI Express connector as well? If so, which ones? With many high and low speed interfaces such as USB, LPC, I2C, SMBus, SPI, SATA, Ethernet, and CAN, available, there were many options facing the committee.
The answer to these questions is highly dependent upon the application. Selection was a controversial and difficult task since at that time the companies did not know about upcoming lowpower processors including Intel’s Atom, AMD’s Fusion, VIA’s Nano and DM&P’s Vortex86 product families. They also did not know which mix of PCI Express, USB, LPC, SPI, and other I/O interfaces would be supported on these new chips. Even today, the mix varies greatly across semiconductor companies and chipset generations.
A third point of contention was how wide the PCIe data lanes should be? One group argued for the “fat pipe” used in VPX and COM Express architectures - a very large step supporting both x1 and x16 PCIe lanes for applications requiring very high performance graphics and/or speed-intensive I/O. The other group, concerned about size, weight, power and cost, thought that PCIe offered so much more capability than PC/104-Plus’ existing capability, that a combination of some x1 and x4 PCIe lanes would be more than sufficient for most applications. More bandwidth supports more powerful processors, but they require more power and cooling of boards in a stack — even requiring heat pipes in some cases. So, what is the correct balance of performance, cost, upward migration, thermal issues, and complexity? Again, it is a function of the application requirements.
Both groups agreed upon the connector technology. It is Samtec’s Q2 double row, high-speed, 15.24mm Q-strip connector system with ground blade in the center. These connectors require a relatively small amount of real estate on a module yet can currently support up to Generation 2 PCI Express data rates of 5 Gbps with a stack of up to 4 boards. This data rate has been tested and verified by Samtec’s Signal Integrity group and is the enabling technology to allow PCIe to be supported within a stack of boards. It also allows both high and low speed signals to be mixed on the same connector.
These first three issues became “showstoppers” and the two groups were unable to reach a consensus. Since one group’s philosophy was to support low to moderate processing applications while the other group focused on moderate to high-speed processing applications, plus their difference of opinion on whether to keep the PC/104 or PCI-104 connector, resulted in the companies agreeing to disagree and go their separate ways. Consequently one group of board manufacturers stayed with the PC/104 Consortium and the other started a group called the Small Form Factor Special Interest Group (SFF-SIG). The SIG consisted primarily of the companies that had previously defined and introduced the successful EPIC form factor standard.
In early 2008, the SFF-SIG introduced SUMIT-ISM. SUMIT stands for Standard Unified Modular Interconnect Technology and it defines a connector and pin out for stacking modules together. On two, 52-pin SUMIT connectors it includes PCIe x1, PCIe x4, USB, LPC, SPI, and SMB channels. ISM stands for Industry Standard Module which is a new name for the popular of 90 × 96mm board outline, in order to phase out the confusing practice of using a single name “PC/104” to refer to a bus sometimes and to a board outline at other times. SUMIT-ISM is defined as an Industry Standard Module with the scalable SUMIT connectors (“and/or” only 52 pins each) placed in the same area as the PCI-104 connector.
A PC/104 connector is also supported in the SUMIT-ISM legacy configuration to allow PC/104 modules to be included in a stack of boards. SUMIT-ISM expansion maintains direct support for the vast number of PC/104 expansion I/O modules and enclosures, necessary for the installed base of hundreds of system manufacturers who would rather not reengineer their ISA-based software at this time. The SUMIT-ISM architects did not assume that there needed to be compatibility with PCI-104 modules since moving from PCI to PCIe doesnít require application software changes. However, a recent update to the ISM definition uses slotted mounting holes, allowing a SUMIT-ISM module to be defined and built using either the PC/104 or PCI-104 connector for legacy support.
Also around the same time in 2008, the PC/104 Embedded Consortium introduced PCI/104-Express and PCIe/104, both focused on very high performance applications. They are based upon a 3 bank connector for a total of 156 pins. In Bank 1, the PCIe/104 bus contains four PCI Express x1 links, 2 USB 2.0 ports, SMB, and some control signals. Bank 2 and Bank 3 contain only the PCI Express x16 link. PCI/104-Express is defined with both the PCI-104 and PCIe/104 connectors so that it can connect directly to PCI-104 cards in a stack of boards. Since the PCIe/104 bus is located where the PC/104 ISA bus connector was previously situated, a mezzanine module with a PCI to ISA and BIOS code is needed to allow existing PC/104 modules to operate in the stack, increasing the stack height by 1 card.
In 2011, the Consortium introduced a second pin definition called PCIe/104 Type 2 with the 2008 definition now referred to as Type 1. Bank 1 of the connector remained the same as before, but Banks 2 and 3 were changed. Rather than just supporting the PCI Express x16 link, it is replaced with two x4 PCIe links, two SATA ports, USB 3.0, LPC, and battery power. Other than the graphics card, most existing I/O board designs for PCIe/104 will be compatible with both Types since they only used Bank 1 signals.
As newer technology and faster highspeed serial buses have been standardized for the commercial / consumer PC market, it was necessary to create a bridge from the past to the future for PC/104-based products. The PC/104 Embedded Consortium and the SFFSIG share a common goal to grow the overall PC/104 marketplace by providing new PCI Express-based solutions that can add to the PC/104 ecosystem. Their architectures are similar yet have differences that result in performance, size, thermal, and price differences according to their target applications and markets.
Subscribe today to receive the INSIDER, a FREE e-mail newsletter from Embedded Technology featuring exclusive previews of upcoming articles, late breaking NASA and industry news, hot products and design ideas, links to online resources, and much more.